Skip to content
Veltrix Motorsport
Driver Performance4 min read

Understanding Brake Release and Corner Entry

Where the brake goes on gets all the attention. How it comes off decides how the car turns.

BRAKE PRESSURE · ABRUPT vs PROGRESSIVE RELEASEAPEXRELEASE··· STEERINGPROGRESSIVEABRUPT
Illustrative data

Braking performance is usually judged by a single number: the brake point. It is easy to see, easy to compare and easy to boast about. But the brake point only decides when the corner begins. What happens in the last third of the braking zone — as pressure comes off and steering goes on — decides how the car behaves at the apex.

What the brake does besides slowing the car

Under braking, load moves forward. The front tyres are pressed harder into the surface and can generate more grip; the rear tyres are unloaded and can generate less. The brake pedal is therefore not only a speed control. It is the driver's most direct way of deciding how much grip the front axle has at the moment the car is asked to turn.

Release the brake completely before turning in and that extra front load disappears just when it is needed. The nose rises, the front tyres lose their advantage and the car is reluctant to change direction. The driver experiences this as entry understeer and, very often, blames the setup.

Trail braking: trading one kind of grip for another

A tyre has a finite amount of grip to share between slowing the car and turning it. At full braking in a straight line, all of it is used for slowing. At the apex, nearly all of it is used for turning. Trail braking is the managed handover between the two: brake pressure is reduced progressively as steering angle increases, so the tyre stays close to its limit throughout rather than dropping below it in the middle.

Done well, this keeps the front loaded, helps the car rotate and shortens the distance travelled at low speed. The pedal is not being used to slow the car much by this point — it is being used to steer it.

What it looks like in the data

The shape of the brake pressure trace tells most of the story.

  • A sharp rise to peak pressure — the car is at its fastest, with the most grip and downforce available, so this is where hard braking belongs
  • A short plateau, or a gentle decline as speed and grip fall away
  • A long, smooth taper to zero that overlaps with the build-up of steering angle

An abrupt release looks like a cliff: pressure falls from a high value to nothing in a few metres, well before the steering trace has finished rising. A good release looks like a ramp, and its end coincides closely with the point of minimum speed.

Two further checks are worth making. Plot longitudinal against lateral acceleration and a good entry traces a smooth arc from braking to cornering; a poor one cuts the corner of that plot, showing grip left unused. And look at where the minimum speed occurs — if it arrives well before the apex, the car was slowed too much, too early.

The two ways to get it wrong

Releasing too early or too abruptly is the more common fault, particularly in drivers moving up from lower-grip machinery. The car is settled in a straight line and then asked to turn with no help from load transfer. Minimum speed is low, the car will not rotate, and the throttle has to wait.

The opposite fault is carrying too much pressure too deep. The rear is unloaded while lateral demand is rising, and the car becomes unstable on entry. The driver catches it with a correction, which costs time and confidence, and tends to brake earlier on the following lap to avoid a repeat.

Both faults are visible as a mismatch between two traces: brake pressure and steering angle. The aim is not maximum trail braking. It is the amount that suits the corner and the car.

The brake point decides when the corner starts. The release decides how it goes.

It is not the same in every corner

Slow corners that need a large change of direction reward a long release, because rotation is what the car is short of. Fast corners need very little, because the car is already loaded by speed and aerodynamics, and stability matters more than rotation. A car with a nervous rear needs less than a car that understeers. Part of the skill is recognising which corner, and which car, is in front of you.

Working on it

  • Leave the brake point alone at first. Change only the release, so the effect can be seen clearly
  • Aim to finish releasing at the point of minimum speed, not before it
  • Judge the result by minimum speed and by how early full throttle is reached — not by how the entry felt
  • Work on one corner at a time, and confirm the change is repeatable before moving on

Brake release is one of the few techniques that improves entry, mid-corner and exit at once. It is also one of the hardest to feel from the seat and one of the easiest to see in the data — which makes it an ideal place for driver and engineer to work together.

Want this kind of analysis on your own data?

Start a Conversation